API X52管线钢与Corus RQT 701超高强钢的焊接工艺

针对超高强钢在机械行业的广泛使用,焊接接头易出现淬硬脆化、裂纹等缺陷的情况,采用焊条电弧焊(SMAW)和药芯气体保护焊(FCAW-GS)组合的焊接方法,对API X52管线钢与Corus RQT 701超高强钢的焊接进行了工艺试验,并进行常规力学性能试验。结果表明,通过合理匹配焊接工艺参数,严格控制低热输入量及层间温度,实现了小熔合比的异种钢焊接,且焊接接头具有良好的力学性能,达到了标准和规格书的要求;异种高强钢焊接,采用SMAW打底焊接和FCAWGS填充并盖面的方法,焊接效率较单纯采用焊条电弧焊工艺提高2倍以上。     

内燃机钢制活塞焊接的研究现状

文中分析了内燃机活塞选用钢作原材料、焊接作为连接方法的优点,并概括叙述了摩擦焊、激光-电弧复合焊、真空钎焊在钢制活塞焊接中的探索及应用。焊接式钢制活塞在结构钢度、热效率、经济环保等方面有所提高,且造成的噪声污染较小,从而具有更广阔的发展前景。文中通过分析在3种不同焊接方法下活塞的结构、接头强度、微观组织,总结得出摩擦焊最大问题在于飞边和尺寸,激光复合焊在机械化生产上存在生产成本的问题,而真空钎焊接头在强度及生产效率方面仍需进一步的改善。     

摩擦变形量对异种金属摩擦焊组织和性能影响研究

针对摩擦变形量对异种金属的焊接质量影响情况认识不充分这一问题,开展了摩擦变形量对焊缝组织及力学性能影响规律的研究。基于微观组织、显微硬度和力学性能的对比分析,对调质态42CrMo与正火态36Mn2V管材不同摩擦变形量的连续驱动摩擦焊进行了研究,为其在工程应用提供理论依据。     

Study on stress and deformation of keyhole gas tungsten arc-welded joints

Keyhole gas tungsten arc welding(K-TIG)of Q345 low alloy steel plates was simulated by using SYSWELD software.The temperature field of the K-TIG welding process was simulated with three different combined heat sources and was compared with the weld profile that was obtained experimentally.The temperature field that was obtained by a combination of a double ellipsoid heat source on the upper half and a three-dimensional Gauss heat source on the lower half was similar to the real situation.The effects of plate thickness,gap and welding speed on the deformation and stress of the K-TIG welded joints were investigated by K-TIG welding numerical simulation.A reduction in the thickness of the weld plates reduced the z-direction deformation and transverse residual stress;an appropriate gap reduced the residual stress and an increase in the welding speed reduced deformation after welding,but did not help to control the residual stress after welding.     

Predicting Tensile Properties of Friction-Stir-Welded 6063 Aluminum with Experimentally Measured Welding Heat Input

This work aims to develop a reliable method to predict mechanical properties of friction-stir-welded 6 xxx-series alloys with experimentally measured welding heat input. A calorimetrical method was utilized to experimentally measure the welding heat input in the friction stir welded of aluminum alloy 6063-T5. Good correlations between the input variables, i.e., welding parameters and physical properties of the materials, and the welding heat inputs obtained with experimental measurements were discovered. The welding heat input can be predicted using the empirical equation derived based on these correlations. Moreover, the results suggested that the thermal conductivities of the welded alloys affected the welding heat input significantly. Mechanical properties, including hardness and tensile properties, of friction-stir-welded aluminum alloy 6063 were in good correlation to the heat input obtained with experimental measurement. These correlations were explained by the evolution of the strengthening precipitates during welding. This work proposed a reliable new route to predict these mechanical responses through the estimation of heat input.     

某新型X光管轴承内轴断裂分析

X光管是用来产生X射线的主要元件,轴承是X光管的关键器件之一。由轴身和法兰焊接而成的轴承内轴发生断裂。采用对断裂的轴承内轴进行了金相分析、断口检验、硬度检测及焊接质量检验,以揭示其断裂的原因。结果表明:轴身与法兰没有焊透,且焊缝有裂纹,导致其断裂。提出了几点关于预防轴承内轴断裂的建议。     

拉锻式摩擦塞焊的热力耦合解析模型和试验验证

为快速得到拉锻式摩擦塞焊的焊接工艺参数，对焊接过程进行预测，建立了摩擦塞焊过程的扭矩、轴向力、功率和能量等指标的力学模型和热力耦合解析模型。模型的输入量为焊接塞棒的几何参数、材料属性、焊接转速和进给速度，输出量为焊接过程的扭矩、轴向力、功率和能量等。在自主设计的拉锻式摩擦塞焊设备上进行了焊接试验。通过将试验数据的输入和输出指标与理论模型值进行对比分析，验证了理论解析模型的可行性。     

焊接热输入对2219薄板铝合金焊接接头性能的影响

针对2219薄板铝合金,采用不同焊接热输入的TIG焊开展了对比试验,分析了焊接接头的力学性能、组织形貌和断裂特征。研究结果表明,单道焊比双道焊的接头抗拉强度的平均值提高了19.6%,断后伸长率基本相同;双道焊的接头在熔合线附近,焊缝区形成柱状枝晶,组织大小不一、形状不规则,热影响区晶粒粗化,几何形态变化,组织形态不均匀,接头在焊接温度升高时,晶粒粗化,强度降低,断口呈现了沿晶界撕裂扩展的痕迹,局部呈“河流花样”特征;单道焊的接头在熔合线附近,焊缝区等轴晶分布较多,组织均匀一致,晶粒细小,接头在经历了加热、快速冷却、常温放置后,强化相溶于固溶体,Cu原子扩散、聚集,产生点阵畸变,晶粒得到细化,强度升高,断口呈现了典型的塑形断裂痕迹,韧窝形态明显。     

基于数值模拟的挤压参数对AZ91镁合金管转角焊合室分流挤压焊合压力的影响规律研究

提出了一种镁合金管材转角焊合室分流挤压新工艺，该工艺可在有效延长焊合室长度和焊合时间前提下保证舌针刚度，从而保证管材尺寸精度，并且可通过转角剪切变形机制增加预焊合金属变形量和动态再结晶程度，从而有利于提高管材性能和焊缝焊合性能。利用有限元法揭示了转角焊合室分流挤压成形过程中金属的流动特征，应变分布特征和焊合室内的静水压力分布特征。结果表明，整个挤压过程无金属折叠，从而保证管材的表面质量；流经转角后预焊合金属变形量明显增加，有利于提高管材质量和焊缝质量。最后，研究揭示了坯料初始温度，挤压速度和模具转角对焊合室内静水压力的影响规律。结果表明，随着挤压速度的增加和模具转角的增大，转角焊合室内静水压力增大；随着坯料预热温度的增加，转角焊合室内静水压力呈先增大后减小的趋势。     

Static and dynamic oxidation behaviour of silicon carbide at high temperature

SiC has extensive applications in high-temperature oxidation environments. However, few studies have investigated the differences between the static and dynamic oxidation behaviour. In this study, the static and dynamic oxidation of SiC were investigated in air and in plasma wind tunnels, respectively. The results demonstrated that the activation energy of static oxidation was ～68.02 kJ/mol at 1300–1600 ℃, which was approximately ten times that of dynamic oxidation ～7.05 kJ/mol at 1290–1534 ℃. The observed Si-O-C transition layer located at the SiO₂/SiC interface, and its thickness after dynamic oxidation for 300 s was thicker than that after static oxidation for 30 h. In dynamic oxidation, high-speed flowing atomic oxygen reacted directly with SiC, whereas molecular oxygen needed extra energy to break the OO bond and react with SiC in static oxidation. Atomic oxygen also migrated easier in the amorphous SiO₂ coating, contributing to a thicker Si-O-C layer and lower activation energy.